Wednesday, August 05, 2026
Happening Now in Welding Industry
Porosity suppression and mechanical properties of laser-TIG hybrid welded joints
Featured Story

Porosity suppression and mechanical properties of laser-TIG hybrid welded joints

Researchers applied laser-TIG hybrid welding to 4 mm T6-tempered Al-7Mg-3Zn alloy for lightweight rail-transit car bodies. At 2.4 kW laser power, poro

3,533 chars 3 min read Industry News
0.66%
Minimum Porosity
298.32 MPa
Tensile Strength
10.23%
Elongation
2.4 kW
Optimal Laser Power

Electric Welding Machine / MCP search supplement August 05, 2026

A new Chinese welding study targets one of the persistent barriers to lightweight rail-transit manufacturing: porosity and softening in fusion-welded aluminum alloys. Researchers from CRRC Qingdao Sifang, Harbin Institute of Technology, the Shandong Key Laboratory of Special Welding Technology, and the Shandong Marine Technology Research Institute investigated laser-TIG hybrid welding of 4 mm thick T6-tempered Al-7Mg-3Zn alloy, a candidate material for lighter railcar bodies.

Published in the July 2026 issue of Electric Welding Machine, the paper systematically tested laser power levels of 2.0 kW, 2.4 kW, and 2.8 kW. The team evaluated weld formation, porosity, microhardness, HAZ softening, and room-temperature tensile behavior using metallographic observation, ImageJ analysis, and mechanical testing.

The results showed that higher laser power increased both weld width and penetration monotonically: width rose from 4.4 mm to 4.9 mm, while penetration increased from 2.8 mm to 3.5 mm. However, porosity did not follow the same straight-line trend. At 2.0 kW, the measured porosity was 0.87%; it dropped to a minimum of 0.66% at 2.4 kW; and it then jumped sharply to 2.28% at 2.8 kW.

According to the study, that non-monotonic pattern reflects two competing physical mechanisms. At lower power, a larger molten-pool volume and slower cooling rate give gas bubbles more time to escape. At higher power, severe evaporation of low-boiling-point elements such as magnesium and zinc destabilizes and collapses the keyhole, trapping pores in the solidifying weld.

Mechanical performance tracked porosity closely. The best overall joint was produced at 2.4 kW, where ultimate tensile strength reached 298.32 MPa, elongation was 10.23%, and heat-affected-zone softening was minimized at 16.9%. The authors conclude that laser power must be tuned not simply for penetration, but to balance keyhole stability, molten-pool dynamics, and defect escape.

For the Chinese rail sector, the findings are practical rather than purely academic. Aluminum alloys reduce vehicle weight and energy use, but fusion welds can suffer from pore-related strength loss and localized softening. The study gives process engineers a clearer window for optimizing laser-TIG hybrid parameters: enough energy to achieve consistent penetration, but not so much that volatile alloying elements undermine keyhole stability.

The paper also underscores how China’s welding research is increasingly tied to industrial application scenarios. The work was supported by the National Key Research and Development Program and directly addresses materials and fabrication conditions relevant to rail-transit equipment manufacturing.

The broader takeaway is that laser-arc hybrid welding remains a promising route for high-strength aluminum structures, but process windows can be narrow. Small changes in laser power can shift a joint from acceptable porosity to unstable keyhole behavior. For manufacturers, the research supports tighter parameter control, stronger process monitoring, and continued development of hybrid welding methods that combine laser penetration with the gap tolerance and arc stability of TIG welding.

As lightweighting pressures grow in rail, automotive, and aerospace manufacturing, studies that connect porosity mechanisms to measurable tensile performance are likely to remain valuable. This one suggests that the path to reliable aluminum welds lies in understanding the physics inside the molten pool, not merely increasing power.

Technology & Innovation
TechAug 2026
Chinese Laser Welders: Quality Meets Innovation on The Global Stage - Leapion

Chinese laser welders are making a significant impact on the global market due to their cost-effectiveness and advanced technology. The development history showcases China's commitment to innovation, leading to improvements in accuracy, power effi...

Source: Leapion
TechAug 2026
China Best Spot Welder What Makes It Stand Out?

China's spot welders are gaining recognition in manufacturing due to their innovative technology, including advanced control systems for enhanced precision and high-frequency transformers for rapid heating and increased productivity. The industry ...

Source: vertexaisearch.cloud.google.com
TechAug 2026
Sinopec No. 1 Construction uses pipeline welding robots with 100% weld pass rate

Sinopec No. 1 Construction Co. and Nanjing University of Science and Technology have deployed a new generation of pipeline intelligent welding robots using 3D laser vision, trajectory planning and welding-process databases. In one project, 320 wel...

Source: Toutiao / Workercn
TechAug 2026
Xiaoyu Zhizao launches 169,800 yuan embodied-intelligence welding robot for non-standard production lines

Xiaoyu Zhizao says its industrial embodied-intelligence welding robot starts at 169,800 yuan and has been deployed in shipbuilding and steel-structure plants, with reported weld pass rates above 99.5%. The system uses a 3D camera, UR arm, AI chip ...

Source: Sina Finance
TechAug 2026
Estun intelligent factory uses robots to build robots and expands AI welding applications

Nanjing Estun's intelligent factory can autonomously produce more than 90 industrial robot models and has deployed over 200 robots in one NEV production line. The company says laser-camera weld recognition, AI trajectory generation and planned sel...

Source: Toutiao / Xinhua Daily
Industry News
IndustryAug 2026
Porosity suppression and mechanical properties of laser-TIG hybrid welded joints in new high-strength Al-Mg-Zn alloy

Researchers applied laser-TIG hybrid welding to 4 mm T6-tempered Al-7Mg-3Zn alloy for lightweight rail-transit car bodies. At 2.4 kW laser power, porosity fell to 0.66%, tensile strength reached 298.32 MPa, elongation was 10.23%, and HAZ softening...

Source: Electric Welding Machine
IndustryAug 2026
TISCO Stainless secures patent for laser welding process for T4003 ferritic stainless steel

Shanxi Taigang Stainless Steel reports a national patent for a laser welding method for T4003 ferritic stainless steel, addressing a manufacturing gap in high-end structural stainless steel pipe. The company says it has added 97 authorized patents...

Source: Metallurgical Information Network
IndustryAug 2026
Chinese research project solves embrittlement in high-heat-input welding steel

A National Natural Science Foundation project led by Hebei University of Science and Technology used oxide metallurgy and microalloying to control coarse grains and toughness loss in the heat-affected zone of heavy plate during high-heat-input wel...

Source: Metallurgical Information Network
IndustryAug 2026
Limah to showcase ultra-thin-wall precision welding systems at Wuxi semiconductor exhibition

Kunshan Limah Automation will present automatic welding machines for AI liquid-cooling manifolds, energy-storage piping and thin-wall bellows at CSEAC 2026 in Wuxi. The company says its systems handle walls as thin as 0.03 mm and support stainless...

Source: Toutiao
Events & Conferences
EventsAug 2026
29th Beijing Essen Welding and Cutting Fair closes in Shenzhen; 2027 show set for Shanghai

The 29th Beijing Essen Welding and Cutting Fair drew 30,994 visitors, including 2,035 overseas attendees from 86 countries and regions, with 905 exhibitors across more than 80,000 square meters. The 30th edition will be held June 23-25, 2027 in Sh...

Source: The Paper / Chinese Mechanical Engineering Society
EventsAug 2026
Dongguan International Laser Welding and Cutting Exhibition scheduled for November 2026

The 2026 China Dongguan International Laser Welding and Cutting Exhibition will run November 26-28 at the Guangdong Modern International Exhibition Center. Organizers cite rapid growth in laser welding equipment, EV battery manufacturing, aerospac...

Source: Sohu
EventsAug 2026
Shanghai welding and cutting equipment exhibition to focus on green, digital and intelligent systems

The 2026 China Welding and Cutting Equipment Exhibition will be held September 21-23 at the Shanghai New International Expo Centre alongside metallurgy, steel, pipe and heavy-machinery events. The program highlights digital welding power sources, ...

Source: TrustExporter
EventsAug 2026
Wuhan welding, cutting, laser and intelligent manufacturing exhibition set for September 2026

The Wuhan International Welding, Cutting, Laser and Intelligent Manufacturing Exhibition is scheduled for September 22-24 at the Wuhan International Expo Center. The UFI-certified event will cover laser processing, robotic welding, precision cutti...

Source: 11467 Exhibition Information
Market & Industry Trends
MarketAug 2026
Shengshi Weisheng raises hundreds of millions for AI welding robot platform

Shengshi Weisheng completed a several-hundred-million-yuan Series B round for industrial embodied-intelligence welding robots. Its system combines a multimodal process 'brain,' motion-control 'cerebellum' and self-developed hardware, targeting non...

Source: 36Kr
Browse Our News Archive

Explore our complete collection of historical welding industry news, market analysis, and technological developments from previous issues.

View Archive

Top^